PLATU 25

PLATU 25

PLATU 25

Dette er vores seneste design, for info kontakt: veleriamontefusco@onesails.it

Lagerstatus: På lager

Produktnavn Price Excl. Tax
PLATU 25 Mainsail Vantage One™ Black Poly
2.320,00 €
PLATU 25 Mainsail Triradial Contender ZZP 09-13 Black
1.750,00 €
PLATU 25 Jib #1 Vantage One™ Black Poly
1.450,00 €
PLATU 25 Jib #1 Triradial Contender ZZP 06 Black
1.150,00 €
PLATU 25 Jib #2 Vantage One™ Black Poly
1.400,00 €
PLATU 25 Jib #2 Triradial Contender ZZP 09-13 Black
1.260,00 €
PLATU 25 Jib #3 Cross Cut Dacron Contender RS5
960,00 €
PLATU 25 Spinnaker Contender Superlite 50
1.450,00 €

Info

Detaljer

  MAINSAIL JIBS SPINNAKER
Class Insigna  - -
Sail Numbers • -
Measurement •
Battens • • -
Tell Tails • • -
Sail Bag • • •

Tuning Guide

Yderligere information

Tuning Guide

Basic rig setup

  • Position mast step 490mm from the foremost keel bolt (port side)
  • Place a mark on the gunwhale beside the chainplates, and measuring from forestay base mark the opposite side gunwhale exactly the same.
  • measure and mark the center of mast collar at deck with reference to the chainplates' V1 pins.
  • Tension V1 just enough to lock the mast in place, leave all diagonals slack.
  • Hoist a metal measuring tape fixed to a slider inserted in the mast groove up to the cap shrouds height.
  • Center the mast sideways measuring to the two marks previously made on the gunwhales.
  • Center the mast in the partners with reference to the mark previously made on the collar.
  • With the diagonals slack, the mast should be straight enough sideways. If any side bend is present, the mast step will probably have to be moved, and the centering procedure repeated.
  • Once the mast is straight sideways, tension the V1 to the basic setup (19 on the tension gauge, see table below). Tension the D1 to 14, the D2 will have to be hand tight.
  • Prebend in this condition should be close to 50mm.
  • Adjust rake as follows: hoist the measuring tape fully with the main halyard and measure to the upper edge of the lower "P" band (lower mainsail luff limit). Add 2560mm to this measurement, this is your reference length. Check the distance from mainsail full hoist to the lower edge of the transom, and adjust headstay length until it matches the reference distance.

 

 

RIG TRIM
PRO-PT-2M tension gauge & standard turnbuckles - (Ronstan turnbuckles, double the number of turns)

TWS (KN)

V1

D1

Turnbuckle
V1

Turnbuckle
D1

Note

0 - 4

   

-1

-0.5

JIB Light
X-Light
0-13 knots

4 - 8

   

-2

-1

Ref. 8 - 12

19 14 - -

12 - 16

    +2 +1

JIB Medium
14-20 Knots

16 - 20

    +1 +0.5

+20

    +1 - JIB Dacron

 

 


SAIL TRIM


Wind (KN)

0 - 5

6 - 10

10 - 14

14 - 18

18 - 20

+20

Jib

light

light

light

medium

medium

heavy

Inhaulers

max/-5

max int.

max int.

max

-5 / -10 -10 / max. out

Jib leech telltales (%flutter)

70% 50% 50-100% 80-100% 100% 100%

Luff tension

-5 cm -5/-3 cm -3 cm / tight tight

tight

tight

Vang

0 0 0-50% 70-100% 100% 100%

Main leech telltales (%flutter)

70-50% 50% 70-100% 100% 100% 100%

Main traveler from centerline

max
windward
max windw. / +10 max windw. / 0 +20 / -20 cm +20 / -20 cm -20 cm / max leeward

Backstay

off off 0-50% 50-100% 100% fully tight 100% fully tight